Charger, BMS, fuel gauge, 3.3 V and 5 V rails, USB-C and solar inputs, and a Bluetooth LE supervisor on a castellated Feather. Stack it under any Feather host, drop it on a breadboard, or solder it down.
Highlights
- Raw LiPo or Li-ion pouch cells, protected on the board
- USB-C and solar in one part, 10 W continuous
- BTHome to Home Assistant with no integration work
- One register map across Arduino, C and MicroPython
Battery
| Cells | 1S |
|---|
| Chemistries | Li-ion, LiPo, LiHV, LiFePO4, LiSOCl2 primary mode |
|---|
| Battery connector | 3-pin JST-PH (BAT, NTC, GND) |
|---|
| Protection | Overcharge, overdischarge, overcurrent, short circuit, temperature; programmable per chemistry |
|---|
| Fuel gauge | State of charge, voltage, current, temperature, time to empty; ±3 % on LiFePO4 after one cycle (measured) |
|---|
Inputs
| USB-C | 5 V at 0.5, 1.5 or 3 A, read from the CC lines |
|---|
| Solar | 6 to 22 V, MPPT, 10 W continuous, 15 W peak (measured) |
|---|
| Charge current | 50 mA to 3 A in 10 mA steps; default 0.5 C |
|---|
| Charger efficiency | 94 % peak, 91 % at 3 A (measured) |
|---|
| Power path | Load runs from the input while the battery charges; ideal-diode handoff when the input is lost |
|---|
Outputs
| 3.3 V rail | 1.5 A continuous, always on inside the discharge window (measured) |
|---|
| 5 V rail | 2 A continuous, switchable; off by default (measured) |
|---|
| Signals | PG, CHG_DONE, INT, EN5V on jumpered Feather positions; VSYS and VBAT on pads |
|---|
Supervisor
| Supervisor | nRF52840 module, Zephyr firmware, I2C at 0x36 |
|---|
| Bluetooth LE | BTHome v2 broadcast, Battery Service, custom GATT; read-only by default |
|---|
| Idle current | 28 µA outputs unloaded; 42 µA advertising every 2 s; 3 µA in ship mode (measured) |
|---|
| Libraries | Arduino, C, MicroPython; one register map, v1.2 |
|---|
Physical
| Outline | Feather, 50.8 × 22.86 mm, castellated, four mounting holes |
|---|
| Board | 4-layer, ENIG, matte navy |
|---|
| Operating temperature | −40 to 85 °C board; charge and discharge windows set per chemistry |
|---|
Feather header
| 3V | 3V3 · out · Regulated 3.3 V; drives the host's 3V position |
|---|
| EN | EN (host) · out · Pulled low through a jumper closed by default, so the host's own regulator stays off |
|---|
| BAT | — · — · Not connected, by design: the host's charger must never see the battery |
|---|
| USB | — · — · Not connected, so two 5 V sources are never in parallel |
|---|
| 11 | INT · out, open drain · Event interrupt; jumper open by default |
|---|
| A2 | PG · out, open drain · Power good, both rails in regulation; jumper open by default |
|---|
| A3 | CHG_DONE · out, open drain · Charge complete; jumper open by default |
|---|
| A5 | EN5V · in, pulled up · Enable the 5 V rail; jumper open by default |
|---|
| SDA, SCL | I2C · — · Qwiic bus at 3.3 V; the supervisor answers at 0x36 |
|---|
| GND | GND · — · |
|---|
| 5V | 2-position 3.5 mm screw terminal block and a pad · Rated 2 A; switched by EN5V and set5V() |
|---|
| VSYS | Pad and castellation · Raw system rail, battery or input, whichever the power path selects |
|---|
| VBAT | Pad and castellation · Battery terminal after the BMS switch; never the host's BAT position |
|---|
| NTC | Battery connector pin 2 and a pad · 10 kΩ, B = 3435 by default; other B values are a setting |
|---|
Physical
| Mass | 8.6 g |
|---|
| HS code | 8504.40.95 |
|---|
| Origin | Assembled in China; designed and tested in Canada |
|---|
Compliance
- CAN ICES-003(B) / NMB-003(B)
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Contains IC: 8017A-MDBT50Q
- Contains FCC ID: SH6MDBT50Q
- The radio module is exempt from RF exposure evaluation (RSS-102 Issue 6, FCC 47 CFR 2.1091) at any separation distance; keep the antenna area clear of metal.
- RoHS 2011/65/EU and (EU) 2015/863 compliant.
- REACH: contains no SVHC above 0.1 % w/w.
- Country of origin: Assembled in China; designed and tested in Canada.
- Export classification: EAR99. HS 8504.40.95.
No cell is supplied with this board. Set the chemistry jumper for the connected cell before the first charge. Safety: https://www.snowbirdpower.com/docs/safety. Security disclosures: [email protected]. Generated from the product data record on 2026-10-21.
